iFlight ProTek25 Pusher Analog w/RaceCam R1 Micro Camera

GoPro mount vendido por separado.

After our big success with the iFlight ProTek series, we are now happy to announce another member. The ProTek25 Pusher!

Aiming for pilots looking for less weight but great durability, maximum performance but long distance and flight time.

A lot of thought was put into creating the best light pusher style 2.5inch quad on the market.

Cinematic as well as light freestyle is where this rig feels home. Cruising through the smallest gaps, chasing skateboards or just for fun in your backyard. Our iFlight naked Hero8 TPU case kit should be the perfect addition getting nice shots from literally anywhere.

- Durable aerodynamic PP body and carbon two-piece frame construction

Only 8 screws to detach the main plastic body from the carbon frame, motors and electronics. Quick, easy and cheap repair or customization!

- Reversed Pusher-style design for enhanced thrust and efficiency

Propeller thrust can travel without any disturbance of frame or wires; Increased flight time, less noise and less propwash!

- Powerful XING 1404 motors to carry your naked GoPro

Lightweight, efficient and maximum power for it's size; More than enough thrust for cruising and acro flying without restriction!

- Less than 250g weight including 4S 650mAh battery and naked Hero8

This drone is in a sub 250g category which can be used without license and registration in most countries!

Flight time:

Batteries used: iFlight Fullsend 4S

With naked GoPro: 650mAh 3-5min, 850mAh 4-6min
Without naked GoPro: 650mAh 5-7min, 850mAh 6-8min

Features:

- High performance Whoop AIO F4 V1.1 AIO Board (BMI270) to save weight and space

- Butter smooth 1404 4600KV (Link)

- RaceCam R1 Mini 1200TVL 2.1mm 19*19

PRE-TUNED & PRE-SETUP:

- First time using one of our BNFs? We carefully prepared an article on General BNF Guide to make your entry as easy as possible!

- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

- Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Changelog:

August 2021: RaceCam R1 Micro 1200TVL 1.8mm 14*14 changed to RaceCam R1 Mini 1200TVL 2.1mm 19*19

March 2022: Before XING 1404 5500KV changed to XING 1404 4600KV

ProTek25 Pusher BNF Specs:

- Electronics: Whoop AIO F4 V1.1 AIO Board (BMI270)

- Motor: XING 1404 4600KV

- Wheelbase: 108mm

- Body Size: 76.3*76.3mm

- Top plate thickness: 3mm

- Top and bottom plate spacing: 21mm (aluminum standoff height) 

- Propeller size: 2.5 inch

- FC pattern: 25.5*25.5mm / 20*20mm

- FPV cam spacing: 20mm

- Weight: 143.8g (without battery)

ProTek25 Pusher Analog Quad BNF Included Components and Parts

pre-built and tested Quadcopter

- 1x iFlight ProTek25 Pusher Frame

- 1x RaceCam R1 Micro 1200TVL 1.8mm 14*14 changed to RaceCam R1 Mini 1200TVL 2.1mm 19*19

- 1x iFlight Sigma MMCX RHCP 5.8g antenna

- 2x iFlight Nazgul 2525 propeller (Set of 4 - Color May Vary)

- 1x 15x150mm battery strtap

- 1x 15x180mm battery strtap

FC + ESC AIO //  Whoop AIO F4 V1.1 AIO

Size：30.5*30.5mm

Mounting pattern：25.5*25.5mm/φ3mm

Weight: 7.4g

Connector：Micro-USB

MCU：STM32F411

Gyro：BMI270

Blackbox：8MB

BEC  output: 5V 2A

INA pad：nR2

Barometer：no

Constant current：20A，25A（Burst）

Input：2-4S

Current sensor：yes

BLHeli：BLHeli-S

ESC Telemetry：no

Firmware Target：IFLIGHT_F411_PRO

ESC Firmware：Q-H-15

VTX // SucceX Mini Force 5.8GHz 600mW VTX Adjustable

-Power: PIT/25/200/400mW/600mW

-Antenna interface: MMCX

-VTX protocol : IRC Tramp

-Output 40 channels. 

-Size: 29*29mm

-Mounting pattern: 20*20Φ3/25*25 mmΦ2

-Weight: 4g

Additional Suggested Parts

• Radio Controller
• Battery 4S 850mAh (LINK) / 4S 650mAh (LINK)

The Battery Holder is not included and needs to be purchased separately!