Inicio
Hay 294 productos.
Filtros activos
Matek UBEC Duo, 4A/5-12V
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Matek ELRS 2.4G True Diversity RX
RGB LED Status
[Rainbow fade effect], Starting Up
[Green heartbeat], Web update mode enabled
[Slow blink 500ms on/off ], Waiting for connection from transmitter
[Red flashing 100ms on/off], Radio chip not detected
[Orange Double blink then pause], Binding mode enabled
[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration
[Solid single color Connected to a transmitter], color indicates packet rate
Matek Optical Flow 3901-L0X
Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.
There is no detailed datasheet of MSP V2 protocol.
Matek Power Module 12S
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g
Matek 2812 Led Controller V2
If you are looking to add LED lighting to your racing drone the Matek 2812 lighting systems provides a neat plug and play solution. The setup consist of the Matek 2812 LED Controller (this product) and RGB LED Strips available separately – here. The controller boasts seven colour options and seven flashing modes. It has four output channels, so one for each arm on a quadcopter and supports control of up to 48 LEDs in total (12 per channel).
TBS Unify Pro32 Nano 5G8 V1.1
Con el TBS UNIFY PRO32 Nano, hemos aumentado la potencia de salida, mejorado la robustez, disminuido el consumo de energía, se ha añadido la capacidad para funcionalidades increibles y se ha perfeccionado la forma en que se monta en tu dron gracias a su reducido tamaño. En pocas palabras, es el mejor y mas completo nano VTx, preparado para el futuro, de mayor calidad y, en general, algo único jamás realizado antes.
Matek H7A3-Slim Flight Controller
Servicio de Impermeabilización de tu Dron
Te impermeabilizamos tu dron, y lo testeamos en un entorno seguro. Si eliges este servicio no te preocupas de nada, nos encargamos de organizar la recogida del dron en tu casa, y te lo mandamos una vez este impermeabilizado ¡Sin gasto extra para ti!
TBS Crossfire Immortal T V2 Antena
Hemos logrado mejorar la immortal T en durabilidad y sensibilidad de la señal.
Radiomaster 2S 7.4V 6200mAh Lipo Battery
5.8GHz Vitenna 8dBi Directional Antenna RHCP
¡Desafía la gravedad con esta exclusiva IFTRON circularmente polarizad! Diga "Hola" a Vitenna ©. ¡No más problemas de montaje de la antena! Hemos diseñado Vitenna © con un cable coaxial especial de cuello de cisne. El cuello de cisne soporta la antena por sí solo. Simplemente apriete el conector en el receptor SMA y luego doble el vástago para apuntar a Vitenna como desee ... ¡y se queda sola en la posición que quieras! ¿Qué podría ser más simple y más fácil?
Radiomaster RP1 V2
The RP1 and RP2 feature WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone.
Due to the low-latency and high-refresh-rate RF module, the RP1 and RP2 are ideal for FPV races or Long Range. Suitable for many models due to the ultra-light and Nano size, these receivers can fit just about anywhere!