Home
Active filters
BetaFPV 2204 Brushless Motor
BETAFPV 2204 brushless motor is enhenced version basic on the popular 2004 motor. It is smooth-running, powerful, and more controllable specifically designed for the 3” ducted whoop, 4” drone and 5” light blade and low general AUW for 5”. We highly recommend pilots using 2204 motors with 35A AIO Brushless FC, It will bring you a strong power to fly more flexible and durable.
F722 35A AIO Brushless Flight Controller
F722 35A AIO Brushless Flight Controller is very reliable to meet your advanced FPV needs. Comes with an F722 chip this board provides a great performance capability and high processing speed, which brings pilots a stable and smooth flight. Featuring a 6-pin plug&play port, it can directly connect HD Digital VTX with NO soldering work. With the support of up to 6S input voltage, this FC pushes FPV racer to the max.
BETAFPV Cetus X FPV Kit
Whether skillful pilots or new beginners, Cetus X FPV Kit, as the advanced 2S power whoop bundle, is a completely primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. With the combination of Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, get ready for the next level.
Mateksys Flight Controller F405-HDTE
Matek FC H743-Wing V3
The Mateksys H743 series of flight controllers has all the power of the F7 processor, but the H7 now has more ports. This autopilot has up to 13 PWM servo outputs, 7 UART port, 2 i2c and CAN port.
Matek DroneCAN-Digital power monitor
CAN-L4-BM is a ultra-precise digital power monitor based on TI INA239 & ArudPilot AP_Periph firmware. The resistance of this conductive path is 200 μΩ typical, providing low power loss in the application.
With this device, No calibration required, flight controller that support DroneCAN protocol can easily get accurate current & bus voltage readouts via CAN bus.
Matek DroneCAN Magnetometer RM3100
CAN-L4-3100 is a professional grade CAN Magnetometer based on RM3100 & ArudPilot AP_Periph firmware.
Matek Hall effect-Current sensor
Matek FC F405-Wing V2
Mateksys PDB FCHUB-12S V2
PDC
Input voltage range: 8~60V (3~12S LiPo)
4x70A continuous, 4x110A burst
4x ESC power /signal/ telemetry pads
Current Senor: 440A, 3.3V ADC, Scale 75
2x LED indicators for 5V, 12V
1K:20K voltage divider built-in
Matek GNSS M10-L4-3100
Matek F411-WTE
BETAFPV LiteRadio 2 SE Radio Transmitter V2 - FrSky
LiteRadio 2 SE Radio Transmitter is the upgraded version based on LiteRadio 2 and comes with huge improvements. Supports the Frsky / Futaba / Bayang, pilots can easily change Futaba, Frsky D8, Frsky FCC D16, and Frsky LBT D16 mode via the radio transmitter. Comes with 100mW transmitting power, LiteRadio 2 SE brings a wider operating range.
BETAFPV Dipole T Antenna
The dipole T antenna is designed and manufactured by BETAFPV for a 2.4G/915MHz/868MHz receiver. This antenna is omnidirectional. RF balun circuit comes with this dipole antenna, just inside the injected rubber enclosure. Every piece of the antenna is tested with the frequency spectrograph to make sure it works in the correct status.