Home
Active filters
Kotking Water Splashproof Coating for R/C Drone - 15 ml
The best coating for the electronics of your drone and make it waterproof. The coating is easy to remove for repairs or component replacement. The product is 15 ml, enough for coating all the electronics of 2-3 drones.
FuriousFPV External Cable for Smart Power Case V2
GensAce Imars III Smart Balance RC Battery Charger (5A)
GensAce Imars III Smart Balance Charger, capable of 5 amp charge rates, worldwide 100V-240V voltage versatility, with 100 Watts of power. great for your FPV &Car Batteries.
GensAce Imars III Pro Smart Balance RC Battery Charger (10A)
GensAce Imars III Pro Smart Balance Charger, capable of 10 amp charge rates, worldwide 100V-240V voltage versatility, with 100 Watts of power. It is great to charge your FPV & Car Batteries.
GensAce Imars Dual Channel AC200W/DC300Wx2 Smart Balance RC Charger - Europe White
GensAce Imars Dual Channel AC/DC Balance Charger Europe Version, capable of 10 amp charge rates, worldwide 100V-240V voltage versatility, with 100 Watts of power. It is great to charge your FPV / Drone / RC Car Batteries.
GensAce Imars Dual Channel AC200W/DC300Wx2 Smart Balance RC Charger - Europe Black
GensAce Imars Dual Channel AC/DC Balance Charger EU Version, capable of 15 amp charge rates, worldwide 100V-240V voltage versatility, AC 200 Watts, DC 600 Watts. It is great to charge your FPV / Drone / RC Car Batteries.
Mateksys PDB FCHUB-12S V2
PDC
Input voltage range: 8~60V (3~12S LiPo)
4x70A continuous, 4x110A burst
4x ESC power /signal/ telemetry pads
Current Senor: 440A, 3.3V ADC, Scale 75
2x LED indicators for 5V, 12V
1K:20K voltage divider built-in
Matek Hall effect-Current sensor
Matek DroneCAN Magnetometer RM3100
CAN-L4-3100 is a professional grade CAN Magnetometer based on RM3100 & ArudPilot AP_Periph firmware.
Matek DroneCAN-Digital power monitor
CAN-L4-BM is a ultra-precise digital power monitor based on TI INA239 & ArudPilot AP_Periph firmware. The resistance of this conductive path is 200 μΩ typical, providing low power loss in the application.
With this device, No calibration required, flight controller that support DroneCAN protocol can easily get accurate current & bus voltage readouts via CAN bus.
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Matek 2812 Led Controller V2
If you are looking to add LED lighting to your racing drone the Matek 2812 lighting systems provides a neat plug and play solution. The setup consist of the Matek 2812 LED Controller (this product) and RGB LED Strips available separately – here. The controller boasts seven colour options and seven flashing modes. It has four output channels, so one for each arm on a quadcopter and supports control of up to 48 LEDs in total (12 per channel).
Matek UBEC Duo, 4A/5-12V
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g
Matek Power Module 12S
Wide 9V to 55V Operating Input Range with TVS protection
3x independent Step-Down Voltage Regulators
BEC Vx, 5.2V / 6V / 8V output options. supports typical continuous output current of up to 15A, Peak current of up to 25A.
BEC 5V (Fixed), 4A continuous
BEC 12V (Fixed), 4A continuous
1K:20K voltage divider built-in (Volt = 1/21 Input voltage)
Current sensor signal passthrough pad
Size & Weight: 61x40x15mm, 53g