Back In Stock

We waterproof your drone, and test it in a safe environment. If you choose this service, you don't have to worry about anything, we take care of organizing the pickup of the drone at your home, and we send it to you once it is waterproofed ¡Without extra charge!

Steadyview X Screen receiver is the upgrade V3.3 version of steadyview receiver, the receiver merges two signals into one, avoid image tearing and rolling in the multi-path environment, and make the image more stable and clear in challenging condition. The RX has an IPS screen and shuttle wheel, use can the shuttle wheel to set the RX. The SteadyView X receiver has ground station KIT, user can use it on any monitor or goggles which have an AV IN port. Also, the steadyview X have an ELRS backpack build in, user can use the ELRS TX backpack and Lua script to synchronize the VTX and VRX. It supports diversity.

The Pavo25 Whoop Quadcopter is a 2.5-inch FPV pusher drone developed by BETAFPV. The new frame design optimizes its structure to decrease complex components and only requires 6 screws to assemble the whoop duct and drone, which is convenient to build. Made of high-quality PA12 material, it features a strong injected mold frame for durable use. What's more, it supports carrying many FPV cameras available in the market for FPV shots. Also, it adopts Caddx Nebula Pro Nano Vista Kit for the HD Digital version, and Caddx Baby Ratel2+A03 400mW 5.8G for the Analog VTX version. Pavo25 is the cinewhoop for you to fly both indoors and outdoors!

The 450mAh 2S 45C Lipo Battery by BETAFPV owns a more powerful performance with stronger mobility and higher sensitivity under high-speed flight, which is suited for whoop drones and toothpicks! This battery features 2S, XT30 connector with 16AWG silicone wire, 7.4V voltage, and 450mAh capacity. Suitable for Meteor85, Meteor85 HD, Beta75X, Mobula 7, and other 2S brushless Whoop drones in the market.

A03 400mW 5.8G VTX, a video transmitter with OpenVTx firmware, supports both the SmartAudio and Tramp protocols. It features PIT/RCE/25mW/100mW/400mW adjustable output power for different use. With the 26*26mm mounting hole size, it is suitable for whoop or toothpick drones like X-Knight series, Beta85X/95X series, TWIG series and Pavo series.

5V Buzzer for your flight controller

RGB LED Status

[Rainbow fade effect], Starting Up

[Green heartbeat], Web update mode enabled

[Slow blink 500ms on/off ], Waiting for connection from transmitter

[Red flashing 100ms on/off], Radio chip not detected

[Orange Double blink then pause], Binding mode enabled

[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration

[Solid single color Connected to a transmitter], color indicates packet rate

Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.

There is no detailed datasheet of MSP V2 protocol.

Wide 9V to 55V Operating Input Range with TVS protection

3x independent Step-Down Voltage Regulators

BEC Vx,  5.2V / 6V / 8V output options.  supports typical continuous output current of up to 15A, Peak current of up to 25A.

BEC 5V (Fixed), 4A continuous

BEC 12V (Fixed), 4A continuous

1K:20K voltage divider built-in (Volt = 1/21 Input voltage)

Current sensor signal passthrough pad

Size & Weight: 61x40x15mm, 53g

If you are looking to add LED lighting to your racing drone the Matek 2812 lighting systems provides a neat plug and play solution. The setup consist of the Matek 2812 LED Controller (this product) and RGB LED Strips available separately – here. The controller boasts seven colour options and seven flashing modes. It has four output channels, so one for each arm on a quadcopter and supports control of up to 48 LEDs in total (12 per channel).

The RP1 and RP2 feature WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone.

Due to the low-latency and high-refresh-rate RF module, the RP1 and RP2 are ideal for FPV races or Long Range. Suitable for many models due to the ultra-light and Nano size, these receivers can fit just about anywhere!