Inicio
Hay 39 productos.
Filtros activos
Matek UBEC Duo, 4A/5-12V
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Matek ELRS 2.4G True Diversity RX
RGB LED Status
[Rainbow fade effect], Starting Up
[Green heartbeat], Web update mode enabled
[Slow blink 500ms on/off ], Waiting for connection from transmitter
[Red flashing 100ms on/off], Radio chip not detected
[Orange Double blink then pause], Binding mode enabled
[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration
[Solid single color Connected to a transmitter], color indicates packet rate
Matek Optical Flow 3901-L0X
Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.
There is no detailed datasheet of MSP V2 protocol.
ImmersionRC TrampHV
EL transmisor de vídeo de 5.8GHz más avanzado. Solo 4 gramos, y de dimensiones reducidads de 31 x 20mm, el TrampHV también es el vtx más pequeño que se puede alimentar directamente a la LiPo.
Soporta la configuración "touch-free", para cambiar rapidamente de canal o potencia sin que se caliente el vtx. (accesorio aparte)
Matek Power Module 12S
ImmersionRC Tramp Nano (International Version)
El Tramp HV original se lanzó en 2016 y superó los límites de lo que era posible con un transmisor analógico FPV de 5.8GHz.
El Tramp Nano es el primo más pequeño, más adecuado para los modelos ligeros de hoy.
Control a través de la telemetría Betaflight (modo Tramp), botón o varita Touch'n’Race.
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g
ImmersionRC RapidFIRE módulo receptor para gafas FatShark
El mejor de los receptores de 5.8 GHz para gafas FatShark.
Matek 2812 Led Controller V2
If you are looking to add LED lighting to your racing drone the Matek 2812 lighting systems provides a neat plug and play solution. The setup consist of the Matek 2812 LED Controller (this product) and RGB LED Strips available separately – here. The controller boasts seven colour options and seven flashing modes. It has four output channels, so one for each arm on a quadcopter and supports control of up to 48 LEDs in total (12 per channel).
Matek H7A3-Slim Flight Controller
Mateksys Flight Controller F405-HDTE
Matek FC H743-Wing V3
The Mateksys H743 series of flight controllers has all the power of the F7 processor, but the H7 now has more ports. This autopilot has up to 13 PWM servo outputs, 7 UART port, 2 i2c and CAN port.
Matek DroneCAN-Digital power monitor
CAN-L4-BM is a ultra-precise digital power monitor based on TI INA239 & ArudPilot AP_Periph firmware. The resistance of this conductive path is 200 μΩ typical, providing low power loss in the application.
With this device, No calibration required, flight controller that support DroneCAN protocol can easily get accurate current & bus voltage readouts via CAN bus.
Matek DroneCAN Magnetometer RM3100
CAN-L4-3100 is a professional grade CAN Magnetometer based on RM3100 & ArudPilot AP_Periph firmware.