Home
Active filters
Matek UBEC Duo, 4A/5-12V
GoPro mounts
We provide various TPU mounts for your GoPro (Nazgul5, TBS Source One V3...). In case of needing a specific mount, let us know your requirements and we will gladly design a piece that suits you. To specify the wanted 3D print write a message in your order.
iFlight ProTek25 Pusher Analog w/RaceCam R1 Micro Camera
Diatone Roma F5 5inch Freestyle Frame Kit
Effortlessly become one with the wind with the Roma series, created using excellent craftsmanship and surpassing its freestyle predecessors. Fly the Roma frame to get maximum control over your FPV drone.
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Skid protectors
We provide various TPU frame pieces (Nazgul5, TBS Source One V3...). In case of needing a specific piece, let us know your requirements and we will gladly design a piece that suits you. To specify the wanted 3D print write a message in your order.
iFlight Nazgul5 Analog V2 4S 6S FPV Drone
Matek ELRS 2.4G True Diversity RX
RGB LED Status
[Rainbow fade effect], Starting Up
[Green heartbeat], Web update mode enabled
[Slow blink 500ms on/off ], Waiting for connection from transmitter
[Red flashing 100ms on/off], Radio chip not detected
[Orange Double blink then pause], Binding mode enabled
[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration
[Solid single color Connected to a transmitter], color indicates packet rate
BETAFPV Cetus Pro FPV Kit
The Cetus Pro FPV Kit is finally here! It is the best ideal choice for beginners to advance currently. Comes with a Cetus Pro brushless quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles, it's more powerful and maneuverable for all starters as well as FPV pros to practice indoor and outdoor.
Matek Optical Flow 3901-L0X
Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.
There is no detailed datasheet of MSP V2 protocol.
8-axis 30L PRO
Drone specialized in agricultural tasks. The drone comes assembled and ready to fly, with a carrying case included as well a controller, battery and charger. An Android mobile or tablet is required to be able to use all the functions of the drone. We offer long-term support and spare parts.
TBS Source Two V0.1
The SOURCE TWO is the 2nd open source frame, this time focusing on lightweight and racing. The frame is donated to the community to empower creators and makers, and integrate best practices and current trends faster into a continuously manufactured product.
Matek Power Module 12S
Wide 9V to 55V Operating Input Range with TVS protection
3x independent Step-Down Voltage Regulators
BEC Vx, 5.2V / 6V / 8V output options. supports typical continuous output current of up to 15A, Peak current of up to 25A.
BEC 5V (Fixed), 4A continuous
BEC 12V (Fixed), 4A continuous
1K:20K voltage divider built-in (Volt = 1/21 Input voltage)
Current sensor signal passthrough pad
Size & Weight: 61x40x15mm, 53g
6-axis 30L PRO
Drone specialized in agricultural tasks. The drone comes assembled and ready to fly, with a carrying case included as well a controller, battery and charger. An Android mobile or tablet is required to be able to use all the functions of the drone. We offer long-term support and spare parts.
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g