Home
Active filters
Matek UBEC Duo, 4A/5-12V
HQProp Cap
HQProp Cap.
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Matek ELRS 2.4G True Diversity RX
RGB LED Status
[Rainbow fade effect], Starting Up
[Green heartbeat], Web update mode enabled
[Slow blink 500ms on/off ], Waiting for connection from transmitter
[Red flashing 100ms on/off], Radio chip not detected
[Orange Double blink then pause], Binding mode enabled
[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration
[Solid single color Connected to a transmitter], color indicates packet rate
Caddx Cap (Black)
Caddxfpv Cap (Black)
Matek Optical Flow 3901-L0X
Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.
There is no detailed datasheet of MSP V2 protocol.
Gemfan Monkey Hat
Gemfan Monkey Hat
ImmersionRC TrampHV
The most advanced 5.8GHz Video Transmitter available today. Only 4 grams, and a slender 31 x 20mm, the TrampHV is also the smallest direct LiPo-powered vTx in the business.
Supporting touch-free 'TNR' wands, for low inter-heat times, and full Tx configuration with a bright OLED display. (Accesory sold separately)
Matek Power Module 12S
Wide 9V to 55V Operating Input Range with TVS protection
3x independent Step-Down Voltage Regulators
BEC Vx, 5.2V / 6V / 8V output options. supports typical continuous output current of up to 15A, Peak current of up to 25A.
BEC 5V (Fixed), 4A continuous
BEC 12V (Fixed), 4A continuous
1K:20K voltage divider built-in (Volt = 1/21 Input voltage)
Current sensor signal passthrough pad
Size & Weight: 61x40x15mm, 53g
ImmersionRC Tramp Nano (International Version)
The original Tramp HV was released in 2016, and pushed the boundaries of what was possible with an Analog 5.8GHz FPV Transmitter.
The Tramp Nano is the smaller cousin, more suited to today’s lightweight models.
Control via Betaflight telemetry (Tramp Mode), button, or Touch’n’Race wand.
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g
ImmersionRC RapidFIRE Goggle Module for FatShark googles
Best-in-class 5.8GHz diversity receiver for FatShark googles.
Matek 2812 Led Controller V2
If you are looking to add LED lighting to your racing drone the Matek 2812 lighting systems provides a neat plug and play solution. The setup consist of the Matek 2812 LED Controller (this product) and RGB LED Strips available separately – here. The controller boasts seven colour options and seven flashing modes. It has four output channels, so one for each arm on a quadcopter and supports control of up to 48 LEDs in total (12 per channel).