Home
Active filters
Matek UBEC Duo, 4A/5-12V
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Matek ELRS 2.4G True Diversity RX
RGB LED Status
[Rainbow fade effect], Starting Up
[Green heartbeat], Web update mode enabled
[Slow blink 500ms on/off ], Waiting for connection from transmitter
[Red flashing 100ms on/off], Radio chip not detected
[Orange Double blink then pause], Binding mode enabled
[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration
[Solid single color Connected to a transmitter], color indicates packet rate
Matek Optical Flow 3901-L0X
Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.
There is no detailed datasheet of MSP V2 protocol.
Matek Power Module 12S
Wide 9V to 55V Operating Input Range with TVS protection
3x independent Step-Down Voltage Regulators
BEC Vx, 5.2V / 6V / 8V output options. supports typical continuous output current of up to 15A, Peak current of up to 25A.
BEC 5V (Fixed), 4A continuous
BEC 12V (Fixed), 4A continuous
1K:20K voltage divider built-in (Volt = 1/21 Input voltage)
Current sensor signal passthrough pad
Size & Weight: 61x40x15mm, 53g
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g
Matek 2812 Led Controller V2
If you are looking to add LED lighting to your racing drone the Matek 2812 lighting systems provides a neat plug and play solution. The setup consist of the Matek 2812 LED Controller (this product) and RGB LED Strips available separately – here. The controller boasts seven colour options and seven flashing modes. It has four output channels, so one for each arm on a quadcopter and supports control of up to 48 LEDs in total (12 per channel).
Matek H7A3-Slim Flight Controller
Skyzone Cobra SD
The Skyzone Cobra SD goggles are the diversity version of the Cobra S Goggles and include a Diversity Receiver. The goggles are 16:9 FPV goggles and have an LCD screen with vivid color and high luminance, allowing pilots to see more details while racing. Pilots can wear glasses while using these goggles.
The new OS has two languages to select, and the menu system is easy to navigate. The shuttle wheel and new user interface allow the pilot to set all the settings just by rolling the wheel without taking off the goggles.
Skyzone 04O Pro
The SKYZONE SKY04O PRO is an upgraded version of SKY04O, with a 1920*1080 OLED panel and new 42-degree optics, user can get a better and more immersive FPV experience than SKY04O, with a 1080P OLED panel, which is also a good choice for Walksnail avatar and hd zero HD VRX Module.
Skyzone M5 FPV monitor
The SKYZONE M5F 5.8 GHZ FPV monitor with DVR is a high brightness 5-inch monitor integrated with steadyview receiver, the receiver merges two signals into one, avoids image tearing and rolling, make image more stable and clear. The wheel with classic skyzone UI made the goggles easy to use, the monitor support 1cell 18650 battery, easy to switch battery, also support 2-6S Lipo, easy to power on the field.
Skyzone 04X Pro
The SKY04X PRO is the upgrade version of SKY04X, with new optics and a new OLED panel, the skyzone 04x pro can give pilot 52 degrees of field of view, giving huge immersive fpv experience, also with a new OLED panel, the 1920*1080 resolution, and a 100FPS frame rate, use can have way better experience when using the digital VRX system.
Mateksys Flight Controller F405-HDTE
Matek FC H743-Wing V3
The Mateksys H743 series of flight controllers has all the power of the F7 processor, but the H7 now has more ports. This autopilot has up to 13 PWM servo outputs, 7 UART port, 2 i2c and CAN port.
Matek DroneCAN-Digital power monitor
CAN-L4-BM is a ultra-precise digital power monitor based on TI INA239 & ArudPilot AP_Periph firmware. The resistance of this conductive path is 200 μΩ typical, providing low power loss in the application.
With this device, No calibration required, flight controller that support DroneCAN protocol can easily get accurate current & bus voltage readouts via CAN bus.