Home
Active filters
Matek UBEC Duo, 4A/5-12V
GoPro mounts
We provide various TPU mounts for your GoPro (Nazgul5, TBS Source One V3...). In case of needing a specific mount, let us know your requirements and we will gladly design a piece that suits you. To specify the wanted 3D print write a message in your order.
Diatone Roma F5 5inch Freestyle Frame Kit
Effortlessly become one with the wind with the Roma series, created using excellent craftsmanship and surpassing its freestyle predecessors. Fly the Roma frame to get maximum control over your FPV drone.
TBS Diamond Antenna
A slightly-directional antenna for best signal penetration. Built ultra-durable using lessons learned from TBS Triumph, and designed by none other than IBCrazy!
Matek Loud Buzzer 5V
5V Buzzer for your flight controller
Skid protectors
We provide various TPU frame pieces (Nazgul5, TBS Source One V3...). In case of needing a specific piece, let us know your requirements and we will gladly design a piece that suits you. To specify the wanted 3D print write a message in your order.
Matek ELRS 2.4G True Diversity RX
RGB LED Status
[Rainbow fade effect], Starting Up
[Green heartbeat], Web update mode enabled
[Slow blink 500ms on/off ], Waiting for connection from transmitter
[Red flashing 100ms on/off], Radio chip not detected
[Orange Double blink then pause], Binding mode enabled
[Orange Triple blink then pause], Connected to transmitter but mismatched model-match configuration
[Solid single color Connected to a transmitter], color indicates packet rate
TBS Tracer Nano TX
In a race, microseconds count. Goggles down, thumbs up - are you ready for a true 250Hz radio link? End to end latency: barely noticeable. Nothing else comes close! Thanks to 2.4GHz technology, we took the best from Crossfire and shrunk it down to speed it up. The end result: Smaller antennas, more speed, range for days.
Matek Optical Flow 3901-L0X
Communication between 3901-L0X module and Flight controller via UART MSP V2 protocol supported by INAV and ArduPilot.
There is no detailed datasheet of MSP V2 protocol.
TBS Source Two V0.1
The SOURCE TWO is the 2nd open source frame, this time focusing on lightweight and racing. The frame is donated to the community to empower creators and makers, and integrate best practices and current trends faster into a continuously manufactured product.
ImmersionRC TrampHV
The most advanced 5.8GHz Video Transmitter available today. Only 4 grams, and a slender 31 x 20mm, the TrampHV is also the smallest direct LiPo-powered vTx in the business.
Supporting touch-free 'TNR' wands, for low inter-heat times, and full Tx configuration with a bright OLED display. (Accesory sold separately)
Matek Power Module 12S
Wide 9V to 55V Operating Input Range with TVS protection
3x independent Step-Down Voltage Regulators
BEC Vx, 5.2V / 6V / 8V output options. supports typical continuous output current of up to 15A, Peak current of up to 25A.
BEC 5V (Fixed), 4A continuous
BEC 12V (Fixed), 4A continuous
1K:20K voltage divider built-in (Volt = 1/21 Input voltage)
Current sensor signal passthrough pad
Size & Weight: 61x40x15mm, 53g
ImmersionRC Tramp Nano (International Version)
The original Tramp HV was released in 2016, and pushed the boundaries of what was possible with an Analog 5.8GHz FPV Transmitter.
The Tramp Nano is the smaller cousin, more suited to today’s lightweight models.
Control via Betaflight telemetry (Tramp Mode), button, or Touch’n’Race wand.
Matek Power Module 20S
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Voltage Regulators
Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
Regulator 2 , 5.3V / 8.1V / 12.2V output options. supports typical continuous output current of up to 15A, Peak current of up to 22A.
1K:25K voltage divider built-in for 3.3V based voltage ADC
Size & Weight: 61x40x15mm, 63g